Search results

If they say I don't need a trouble code to tell me I have a miss. If mechanics are telling me to change my plugs..about 45 bucks...I'd change my plugs...and even go crazy and do wires as well 80 bucks..unless it has coil packs...which would give a different code. I saw 9+ people looked at...

If you notice the nut in center of last picture...then go in from there. you can see a cynlinder shape..this is where the bottom bolt for the radius arm threads into. After it was all back together and during 4x4 testing this cyclinder broke loose. This allowed the radius arm to move anytime the...

Search for my thread on front axle replacement in the maintenance shop. pix of the rotor removal are there.

TTb The 97 still has the TTB with radius arms. I just posted and axle removal on the Maintenace shop. Welcome to the forum.

Axle continued I needed to replace the yoke as the old axle and the yoke were worn out. There was nothing left of the inside of the yoke. worn smooth no splines at all. I didn't take any more pictures of this process..because it is a lot of work getting the diff out in order to remove the...

more axle Here are more pix of the process of removing the front axles. right side removing spindle nuts, right side outer wheel bearing, right side spindle right side axle.

Over the weekend I replace u-joints and slip yoke in the front axle of 97 Ranger 4x4 took some pix. First got the truck up and secured on jack stand and rear wheels blocked. I then removed wheels and warn locking hubs. then the brake mounting bracket..left the caliper bolted on (one less thing...

Second opinnion Yep get a second O. I drove a truck till the body fell off with a bad rear main seal. I checked the oil every other fill up. It was losing less then a QT between fills...not great for the enviorment but labor is costly. Might be something the kid could learn..also check with...

If your not seeing a lot of oil on the ground, then it's not that bad. I had a truck with a bad seal, the body fell off before the engine gave out. Just remember to check the oil and keep it up in the full area on the stick. I checked every other fill up. 11000 miles seem a little early. Lots...

Must have been there a long time. even after I surgically removed it I could not get it off the line..like it was rust welded on.

Found it!! much better now!

The yoke is toast, I found a yard that sold me the entire right side of the axle/w diff..etc for 150. so I will be doing the hole deal..maybe a limited slip diff included. Will post pix.

Does anyone know how to tighten up the steering gear. There is supposed to be a lock nut you loosen and then you can tighten up the lash in the gear box. This is on a 97 Ranger.

I lean toward a lifter for your tick..I thinkiing either there is some chunk built up a keep oil from flowing properly. most likely because it doesn't do it all the time. Maybe try an oil treatment like lucas run it a while then flush. Gear shifting problem could be air as said before...Another...

Removed the axle to hardly any groves left on the end of the shaft. I got a new (used) axle from the yard. Replaced the U-joint and installed the new axle. (twice) first time got it in and checked it out seemed fine. Test drive went well for a while then there was a bang and no more front...

www.helminc.com has all the Hayes and Chilton manuals as well as the Ford shop manuals... 45 bucks gets you the Ford shop manuals w/ A LOT more detail then either Hayes or even Chilton. I plan on keeping the 97 Ranger and the 92 F150 for a long time, which makes the shop manuals well worth the...

Your getting 22 in the city, You think it could be better? Unless there was an O2 sensor beyond the cat (you would have a check engine light)..other then pollution there won't be much difference..it is a little less restricted and there fore louder. Is this the only thing that was removed?

WACK O for sure... I let you know the outcome.

Try http://www.helminc.com/helm/Result.asp?Style=&Mfg=FMC&Make=FCT&Model=RANG&Year=1997&Category=&Keyword=&Module=&selected_media=&mscsid=2GVN9LFUJRAR9HXM5S5MEBJX2D8P36Q7 Well that is the link I found my manuals for the 97 danger ranger.

Thanks Bill I have changed these filters dozens...nay hundreds of times. Have had some minor problems before but nothing like this. I'll either cut and splice or replace....or.....AUGH have the dealer deal with it.